Passive radiator tower project

Passive radiator tower project


Designer:
Sebastian

Project Category:
Tower Speakers

Project Level:
Intermediate

Project Time:
8-20 Hours

Project Cost:
$100 – $500

Project Description:
34″ tall, 8″ wide, and 16″ long. About 2.3 cubic feet and about 180 watts rms each. 2 way design. 4 woofers and 1 tweeter crossed at about 3200 hz, simple 1st order. Woofers are wired in series and parallel for a 4 ohm load. Whole impedance is about 4.8 each First time using vinyl wrap and passive radiators. The 5.25″ woofers produce very nice mids and lows and the silk tweeters have really crisp highs and clear mids. Sound quality is outstanding and the bass is super clean and rattles my bedroom and the mirror in the bathroom. The loudness of the bass matches that of my diy Dayton ported 10″ subwoofer. The speakers alone do not need a subwoofer as they produce audible bass down to about 35 hz. Passive radiators are the way to go, they give your speakers twice the bass of using ports.

Design Goals:
Sound quality to match high end speakers. Lots of bass and a beautiful finish

Driver Selection:
Dayton Audio ND140-4 5-1/4″ Aluminum Cone Midbass Driver 4 Ohm
Dayton Audio ND25FA-4 1″ Soft Dome Neodymium Tweeter
Dayton Audio SD175-PR 6-1/2″ Passive Radiator

Enclosure Design:
3/4″ mdf. 2.3 cubic feet sealed.
34″ tall, 8″ wide, and 15″ long.

Crossover Design:
First order 2 way crossed at around 3200 hz

Conclusion:
I am very happy with the end result. It’s just how i pictured it. Very happy with all products i used in this project and will definitely purchase them again in the future for other projects. If you’re curious about using passive radiators i’d suggest trying them out but do some research on them first.

About the Designer:
I am only 19 when i built these and built my first speakers when i was 17 for a school project my senior year. I’ve built tower speakers, home subwoofers, car subwoofers, and install car stereos. I love audio, it’s one of my passions.

Project Parts List

Dayton Audio ND140-4 5-1/4″ Aluminum Cone Midbass Driver 4 Ohm
Dayton Audio ND25FA-4 1″ Soft Dome Neodymium Tweeter
Dayton Audio SD175-PR 6-1/2″ Passive Radiator
VViViD XPO Dry Carbon Black Premium Film Vinyl Wrap 5 ft. x 3 ft.
VViViD XPO Dry Carbon Black Premium Film Vinyl Wrap 5 ft. x 1 ft.

3 Comments

Add yours
  1. 1
    cj

    “Passive radiators are the way to go, they give your speakers twice the bass of using ports.”
    Never heard this before (kinda think it’s not true).
    A PR box isn’t sealed, it acts like a vented box.
    A single series coil probably won’t roll these woofers off much at all unless a Zobel was utilized.

  2. 3
    lux

    Great project! I’d like to see more from you.
    Try looking into horn enclosures such as the klipschorn or klipsch jubilee

    @CJ
    “PUMP-12 is designed to add up to +6dB of bass without any need of additional input power when installed in a sealed enclosure.”
    https://www.audioxpress.com/news/earthquake-sound-introduces-new-patented-pump-12-passive-radiator-design
    CJ: “A PR box isn’t sealed, it acts like a vented box.”
    I don’t know where you get that from. The enclosures for passive radiators must be sealed in order to work.
    6dB is a 4 fold increase BTW, so I’m inclined to listen to this young man who has tried this for himself VS your-self who has not tried this at all yet.
    I suggest you: “kinda think” more completely; by trying this for your-self or listening to one for your-self, before coming to conclusions, let alone giving negative feedback without first hand experience.

    A very good crossover design instructional
    http://www.calsci.com/audio/X-Overs.html

    I’ve hardly seen/heard such naysayers or divisive/unproductive input as in audio forums. So, keep your head up and listen to your ears and people with productive input, not the naysayers 😉

    Take care!

Leave a Reply to mikec Cancel reply